WARNING: This product can expose you to chemicals including nicotine, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov
Go With The Flow
Unleash your clouds like never before with the Wulf Mods Flow Auto Flow 510 Voltage Battery! Use your Flow in traditional Auto Draw Mode or switch things up with Auto Flow Mode for a propulsive blast of silky vapor that is truly ferocious. The Flow has some serious claws thanks to its 500mAh battery, choice of 5 temperature settings (1.8, 2.4, 2.8, 3.4. 3.8), and ergonomic aluminum alloy body. With a completely concealed cartridge chamber the Flow is as sleek as it is discreet, making it the ultimate on the go option. The Flow is available in a selection of 5 different colors including pack favorites like black-red spatter and purple-black spatter.
Loading A Cartridge Into The Flow
To begin vaping with your Flow, you must first head into your collection of 510 threaded cartridges and choose one to get started with! From there remove the bottom of your Flow and gently attach the cartridge via the 510 threaded connection port. Once on, carefully replace the bottom of your Flow and prepare for vapor fun!
Using Your Flow
To turn on your Flow Auto Flow 510 Voltage Battery press the power button located on the bottom of the device 5x in a row. When input successfully, your Flow will shine its LED to let you know that you are good to go. After your session concludes, turn off your Flow by repeating the process and pressing your power button 5x in a row.
Adjusting The Flow’s Temperature
To switch between the 5 different temperature settings on the Flow, press the power button on the bottom of the device 1x, this will cycle the voltage to the next level in line. To make viewing your voltage easy, each of the 5 temperature settings has a corresponding LED color, yellow - 1.8v, purple 2.4v, green - 2.8v, blue - 3.4v, and red 3.8v.
Pre-Heating Your Flow
Activate the Flow’s preheat mode by pressing the power button 2x in a row. When done correctly your Flow’s LED will come to life and start slowly cycling through the different colors to let you know your cartridge is being prepared. Once done, the LED’s will turn off and you will be ready to take a special pre heated blast from your Flow!
How To Charge The Flow
To charge your Flow make use of the USB-C port located on the bottom of the device. The first time you charge your Flow, make sure to leave it plugged in for 2 hours. Every single time after that first charge, never leave your Flow plugged in for longer than 1 hour at a time to avoid over charging and short circuiting.
Troubleshooting Your Flow
To make using your Flow as smooth as possible, we recommend that you are aware of the following troubleshooting warnings that can pop up on your device.
- Over Time Warning: Your Flow will flash a red light 4x and switch to standby should you inhale from it longer than 10s at a time.
- Short Circuit Warning: Your Flow will flash a red light 3x to let you know it is experiencing a short circuity, cease to use your device until this warning stops.
- No Cart Warning: Your Flow will flash a white light 3 times if no cartridge is detected.
- Overload Warning: Your Flow will flash a white light 5x to indicate an overload warning.
How To Clean the Flow
Clean your Flow Auto Flow 510 Voltage Battery by first disassembling the bottom and cartridge components, before making use of a q-tip or swab lightly dampened with isopropyl alcohol to gently scrub any build up or grime that has accumulated. Make sure to leave ample time for your Flow to dry before attempting to use it again.
What’s Included:
- (1) Wulf Mods Flow Auto Flow 510 Voltage Battery
Warning: Do not charge with a power bank of 5V or higher. Do not charge in your car. Do not overcharge the battery. Failure to follow these instructions could result in battery damage and frying of the internal system. If the device gets too hot while you are using it, please stop using it for a while. Please avoid using the device while it is charging.